Polymer-modified MXene thin-film nanocomposite membranes for forward osmosis
Abstract
Water scarcity demands novel solutions to address the challenges posed by increasing societal needs. This study presents a novel strategy for fabricating MXene-based thin-film nanocomposite forward osmosis (TFN-FO) membranes with enhanced permeability and selectivity, offering a promising advancement in water treatment technologies. The approach involves synthesizing MXene-functionalized polyvinylpyrrolidone (PVP-g-MXene) additives through a facile chemical grafting method, where hydroxyl groups serve as linkers to covalently bond PVP onto the surface of 2D MXene nanosheets. Subsequently, PVP-g-MXene is incorporated into a polyamide (PA) thin film via interfacial polymerization (IP) to produce the innovative TFN-FO membranes. Characterization of MXene and PVP-g-MXene was performed using FT-IR, XRD, TGA, and FE-SEM. The fabricated membranes were analyzed for surface morphology, roughness, and hydrophilicity using FESEM, AFM, and water contact angle (WCA) measurements. The results indicate that incorporating PVP-g-MXene significantly alters the physicochemical properties of the membranes, including morphology, roughness, hydrophilicity, and overall performance during the IP process. All modified membranes demonstrated improved water flux compared to the pristine TFC membrane, with TFN-PgM1 and TFN-PgM2 exhibiting superior selectivity. Notably the representative TFN-PgM2 membrane exhibited a water flux of 18.5 LMH, which is approximately 72% higher than that of the TFC membrane, and demonstrated a Js/Jw ratio of 0.167, indicating an 18.1% improvement in selectivity performance. These findings demonstrate the effectiveness of polymer-modified MXene for the development of high-performance FO membranes.
Related
- Response-surface optimization of high-performance GO-PET-PEG forward osmosis membranes for bentazone removal
- Assessment of fate of contaminants of emerging concern in forward osmosis-reverse osmosis-anaerobic digestion hybrid: A literature-based approach
- Hydroxy artificial water channels enable ultraselective reverse osmosis membranes for N-nitrosamine removal in water reuse
- Polyamide Reverse Osmosis Membranes Are Less Crosslinked Than Previously Thought
- Integrated Process Environmental and Economic Modeling of Electrically Assisted Forward Osmosis Microbial Desalination for Water and Struvite Recovery
BibTeX
@article{bashardoust2026polymermodified,
title = {{Polymer-modified MXene thin-film nanocomposite membranes for forward osmosis}},
author = {Aidin Bashardoust and Prokopios Georgopanos and Alireza Shakeri},
journal = {Scientific Reports},
year = {2026},
month = oct,
doi = {10.1038/s41598-026-73603-7},
url = {https://www.nature.com/articles/s41598-026-73603-7},
note = {CC BY 4.0},
}
RIS
TY - JOUR
TI - Polymer-modified MXene thin-film nanocomposite membranes for forward osmosis
AU - Aidin Bashardoust
AU - Prokopios Georgopanos
AU - Alireza Shakeri
PY - 2026
DA - 2026/10/14
JO - Scientific Reports
DO - 10.1038/s41598-026-73603-7
UR - https://www.nature.com/articles/s41598-026-73603-7
AB - Water scarcity demands novel solutions to address the challenges posed by increasing societal needs. This study presents a novel strategy for fabricating MXene-based thin-film nanocomposite forward osmosis (TFN-FO) membranes with enhanced permeability and selectivity, offering a promising advancement in water treatment technologies. The approach involves synthesizing MXene-functionalized polyvinylpyrrolidone (PVP-g-MXene) additives through a facile chemical grafting method, where hydroxyl groups serve as linkers to covalently bond PVP onto the surface of 2D MXene nanosheets. Subsequently, PVP-g-MXene is incorporated into a polyamide (PA) thin film via interfacial polymerization (IP) to produce the innovative TFN-FO membranes. Characterization of MXene and PVP-g-MXene was performed using FT-IR, XRD, TGA, and FE-SEM. The fabricated membranes were analyzed for surface morphology, roughness, and hydrophilicity using FESEM, AFM, and water contact angle (WCA) measurements. The results indicate that incorporating PVP-g-MXene significantly alters the physicochemical properties of the membranes, including morphology, roughness, hydrophilicity, and overall performance during the IP process. All modified membranes demonstrated improved water flux compared to the pristine TFC membrane, with TFN-PgM1 and TFN-PgM2 exhibiting superior selectivity. Notably the representative TFN-PgM2 membrane exhibited a water flux of 18.5 LMH, which is approximately 72% higher than that of the TFC membrane, and demonstrated a Js/Jw ratio of 0.167, indicating an 18.1% improvement in selectivity performance. These findings demonstrate the effectiveness of polymer-modified MXene for the development of high-performance FO membranes.
SN - 2045-2322
ER -