Nonlinear control design for stabilization and tracking of a rotary inverted pendulum
- 1Department of Electrical Engineering, Hamedan University of Technology
Abstract
This paper proposes a nonlinear controller framework for the tracking and stabilization control of rotary inverted pendulum (RIP) systems. These systems present significant control challenges due to their underactuation, high sensitivity, and inherent instability. Most existing studies rely on linearized models of RIP systems. However, these approaches limit the controller’s performance to a small area around the equilibrium point. On the other hand, applying advanced nonlinear control techniques to the RIP underactuated system remains challenging. To overcome these limitations, the second-order sliding mode controller (SOSMC) based on a PID sliding surface is developed and applied to the RIP system. The designed procedure incorporates the nonlinear dynamic model to stabilize the pendulum in a greater region and address the challenges of underactuation. The designed control scheme enhances the system performance in stabilizing the pendulum in the vertical upright position and maintaining its balance when the horizontal arm tracks a desired trajectory. The efficacy of the designed controller is compared with three other control approaches: a standard sliding mode control (SMC), a reinforced PID-SMC, and a linear quadratic regulator (LQR). The simulation results demonstrate that the proposed controller scheme exhibits high-speed tracking performance with reduced overshoot. The results show that the Mean Square Error (MSE) for the arm angle is decreased to 0.2229, compared to 0.22346 for reinforced PID-SMC, 0.2250 for SMC, and 0.2299 for LQR. Moreover, the MSE for the pendulum angle is reduced by approximately 69.36%, 28.6%, and 25.68% compared to the reinforced PID-SMC, SMC, and LQR algorithms, respectively. Furthermore, the designed controller achieves a 41.99%, 10.06%, and 18.33% reduction in the RMS value of the control input compared to the reinforced PID-SMC, SMC, and LQR controllers, respectively. The simulation results reveal that the designed controller achieves superior tracking accuracy, faster response, and reduced overshoot, while maintaining efficient energy consumption.
Related
- Myocardial Stiffness Tracking & Assessment Toolkit Driven by Artificial Intelligence For Reproducible Benchmarking of Temporal Segmentation and Shear-Wave Velocity Stabilization on Synthetic Data
- Effects of pulse-type near-fault ground motions on the nonlinear seismic response of steel frames with inverted-V CBF and EBF systems
- A nonlinear exaggerated kernel framework for expressive hair motion in tracking solution-based simulation
- When Habits Dominate in Obsessive-Compulsive Disorder: Tracking the Temporal Dynamics of Habitual and Goal-Directed Control
- Multimodal eye-tracking reveals impaired inhibitory control and reduced preparatory pupil dilation in essential tremor.
BibTeX
@article{shalbafian2026nonlinear,
title = {{Nonlinear control design for stabilization and tracking of a rotary inverted pendulum}},
author = {Arefe Shalbafian and Farhad Amiri},
journal = {Scientific Reports},
year = {2026},
month = jun,
doi = {10.1038/s41598-026-57277-9},
url = {https://doi.org/10.1038/s41598-026-57277-9},
note = {CC BY},
}
RIS
TY - JOUR
TI - Nonlinear control design for stabilization and tracking of a rotary inverted pendulum
AU - Arefe Shalbafian
AU - Farhad Amiri
PY - 2026
DA - 2026/06/01
JO - Scientific Reports
DO - 10.1038/s41598-026-57277-9
UR - https://doi.org/10.1038/s41598-026-57277-9
AB - This paper proposes a nonlinear controller framework for the tracking and stabilization control of rotary inverted pendulum (RIP) systems. These systems present significant control challenges due to their underactuation, high sensitivity, and inherent instability. Most existing studies rely on linearized models of RIP systems. However, these approaches limit the controller’s performance to a small area around the equilibrium point. On the other hand, applying advanced nonlinear control techniques to the RIP underactuated system remains challenging. To overcome these limitations, the second-order sliding mode controller (SOSMC) based on a PID sliding surface is developed and applied to the RIP system. The designed procedure incorporates the nonlinear dynamic model to stabilize the pendulum in a greater region and address the challenges of underactuation. The designed control scheme enhances the system performance in stabilizing the pendulum in the vertical upright position and maintaining its balance when the horizontal arm tracks a desired trajectory. The efficacy of the designed controller is compared with three other control approaches: a standard sliding mode control (SMC), a reinforced PID-SMC, and a linear quadratic regulator (LQR). The simulation results demonstrate that the proposed controller scheme exhibits high-speed tracking performance with reduced overshoot. The results show that the Mean Square Error (MSE) for the arm angle is decreased to 0.2229, compared to 0.22346 for reinforced PID-SMC, 0.2250 for SMC, and 0.2299 for LQR. Moreover, the MSE for the pendulum angle is reduced by approximately 69.36%, 28.6%, and 25.68% compared to the reinforced PID-SMC, SMC, and LQR algorithms, respectively. Furthermore, the designed controller achieves a 41.99%, 10.06%, and 18.33% reduction in the RMS value of the control input compared to the reinforced PID-SMC, SMC, and LQR controllers, respectively. The simulation results reveal that the designed controller achieves superior tracking accuracy, faster response, and reduced overshoot, while maintaining efficient energy consumption.
SN - 2045-2322
ER -