2,4-Dichlorophenol Photodegradation by Novel Burtite-like Solid Solutions: Effect of Sn4+ and Al3+ Content on the Physicochemical Properties and Photocatalytic Performance
- 1Benemérita Universidad Autónoma de Puebla , , Avenida San Claudio y 18 Sur , , ,
- 2Universidad Autónoma Metropolitana Iztapalapa , , Av. San Rafael Atlixco No. 189 , Iztapalapa, ,
Abstract
Nowadays, tailoring the physicochemical properties of novel photocatalysts is crucial for advanced environmental remediation technologies. Thus, in this work, novel solid solutions of burtite-like compounds with nominal Sn amounts of 5.3–27.8 mol % were synthesized. Materials were prepared by the co-precipitation method followed by a hydrothermal treatment. A material without tin was also prepared as a control, and all materials were characterized by X-ray powder diffraction, scanning electron microscopy, nitrogen adsorption–desorption at −196 °C, diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy. To verify their photocatalytic behavior, all samples were tested for the photocatalytic degradation of 2,4-dichlorophenol (a very toxic and recalcitrant pesticide) as a probe molecule. Aeroxide TiO2 P25 was also evaluated by means of comparison under the same experimental conditions. Results revealed that the amount of tin defined the crystalline phases found in the samples since compounds with low tin amounts (below 10%) produced mixtures of hydrocalumite, katoite, and burtite. On the other side, higher tin contents produced pure burtite-like phases. The obtained solid solutions were verified by cell parameter calculations and the absence of secondary crystalline phases. A new acicular morphology of burtite was obtained and assigned to the aluminum-rich solid solution. Photocatalytic experiments demonstrated that all synthesized materials were active under UV irradiation; however, the highest activity was achieved by the katoite/burtite composite (Al-B2), reaching an apparent DiPhe degradation of 54% after 30 min (estimated from UV–vis measurements), while TiO2 exhibited a degradation of 25%. Additionally, 75.5% mineralization was achieved after 2 h, while only 53.8% was attained with TiO2. The most active material was evaluated over six consecutive cycles, with photocatalytic activity dropping from 70% to 25% mineralization between the first and sixth runs due to a lixiviation process. Results demonstrated that burtite’s structure can be modified and its physicochemical characteristics can be adjusted to produce potential photocatalytic materials.
Related
- Heteroatom-engineered SWCNT/TiO2 heterojunctions for enhanced photocatalytic charge transfer and pollutant photodegradation
- Flue Gas Torrefaction of Corn Stover-Densified Fuel: Impacts on Physicochemical Properties and Combustion Performance
- Ionic Liquid Mixtures in Task-Specific Applications: Linking Composition, Physicochemical Properties, and Performance
- Selectivity of acid–base extraction routes and their effects on the structure, physicochemical properties, and adsorption performance of shrimp-shell-derived chitosan
- First principles study of chalcogen vacancy effect on the optoelectronic and photocatalytic properties of transition metal dichalcogenides monolayers
BibTeX
@article{reyescruz202624dichlorophenol,
title = {{2,4-Dichlorophenol Photodegradation by Novel Burtite-like Solid Solutions: Effect of Sn4+ and Al3+ Content on the Physicochemical Properties and Photocatalytic Performance}},
author = {Federico Manuel Reyes-Cruz and Manuel Sánchez-Cantú and Clara Tzompantzi-Flores and Irving I. Ruiz-López and Angela-Gabriela Romero-Villegas and Francisco Tzompantzi},
journal = {ACS omega},
year = {2026},
month = oct,
doi = {10.1021/acsomega.6c04908},
url = {https://europepmc.org/article/PMC/PMC13670345},
note = {CC BY},
}
RIS
TY - JOUR
TI - 2,4-Dichlorophenol Photodegradation by Novel Burtite-like Solid Solutions: Effect of Sn4+ and Al3+ Content on the Physicochemical Properties and Photocatalytic Performance
AU - Federico Manuel Reyes-Cruz
AU - Manuel Sánchez-Cantú
AU - Clara Tzompantzi-Flores
AU - Irving I. Ruiz-López
AU - Angela-Gabriela Romero-Villegas
AU - Francisco Tzompantzi
PY - 2026
DA - 2026/10/01
JO - ACS omega
DO - 10.1021/acsomega.6c04908
UR - https://europepmc.org/article/PMC/PMC13670345
AB - Nowadays, tailoring the physicochemical properties of novel photocatalysts is crucial for advanced environmental remediation technologies. Thus, in this work, novel solid solutions of burtite-like compounds with nominal Sn amounts of 5.3–27.8 mol % were synthesized. Materials were prepared by the co-precipitation method followed by a hydrothermal treatment. A material without tin was also prepared as a control, and all materials were characterized by X-ray powder diffraction, scanning electron microscopy, nitrogen adsorption–desorption at −196 °C, diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy. To verify their photocatalytic behavior, all samples were tested for the photocatalytic degradation of 2,4-dichlorophenol (a very toxic and recalcitrant pesticide) as a probe molecule. Aeroxide TiO2 P25 was also evaluated by means of comparison under the same experimental conditions. Results revealed that the amount of tin defined the crystalline phases found in the samples since compounds with low tin amounts (below 10%) produced mixtures of hydrocalumite, katoite, and burtite. On the other side, higher tin contents produced pure burtite-like phases. The obtained solid solutions were verified by cell parameter calculations and the absence of secondary crystalline phases. A new acicular morphology of burtite was obtained and assigned to the aluminum-rich solid solution. Photocatalytic experiments demonstrated that all synthesized materials were active under UV irradiation; however, the highest activity was achieved by the katoite/burtite composite (Al-B2), reaching an apparent DiPhe degradation of 54% after 30 min (estimated from UV–vis measurements), while TiO2 exhibited a degradation of 25%. Additionally, 75.5% mineralization was achieved after 2 h, while only 53.8% was attained with TiO2. The most active material was evaluated over six consecutive cycles, with photocatalytic activity dropping from 70% to 25% mineralization between the first and sixth runs due to a lixiviation process. Results demonstrated that burtite’s structure can be modified and its physicochemical characteristics can be adjusted to produce potential photocatalytic materials.
SN - 2470-1343
ER -