Analysis of contact fatigue behavior of 18CrNiMo7-6 gears based on surface integrity and microstructure
- 1School of Mechanical Engineering, Tongji University
- 2China Academy of Machinery Science & Technology Qingdao Branch Co., Ltd
Abstract
This study aims to clarify how different initial surface states affect the micropitting and pitting behavior of carburized 18CrNiMo7-6 gears. Gears subjected to grinding, shot peening, and shot peening followed by barrel finishing were tested under the same contact fatigue conditions for a preset duration of 5.0 × 107 cycles. Case 1-SPC consisted of carburizing and grinding, followed by shot peening and barrel finishing. Case 2-SPS consisted of carburizing and grinding, followed by shot peening. Case 3-RC consisted of carburizing and grinding only. The results show that micropitting and pitting are governed by the coupled evolution of surface topography, hardness gradient, residual stress, and near-surface microstructure. All cases exhibited near-surface softening after cycling, while the redistribution of the hardness gradient strongly depended on the initial surface state. Shot peening introduced a high magnitude compressive residual stress field, and after cycling the maximum compressive residual stress in Case 1-SPC remained as high as 977.85 MPa, although this condition also showed the most pronounced stress relaxation. In contrast, barrel finishing produced a smoother and more surface oriented compressive stress distribution with better stability, and Case 1-SPC exhibited the best resistance to both micropitting and pitting. Surface observations showed a regional micropitting band in Case 1-SPC, denser micropitting in Case 2-SPS, and larger localized pitting in the ground condition. In addition, cyclic contact loading induced grain refinement, elevated local orientation gradients, and enhanced plastic heterogeneity in the near-surface layer. After cycling, Case 1-SPC showed the most pronounced microstructural reconstruction, with an average grain size refined to 0.57 μm and an average geometrically necessary dislocation (GND) density increased to 19.99 × 1014 m-2. Overall, shot peening followed by barrel finishing provided the most favorable balance among residual stress stability, surface integrity retention, and damage suppression, and was therefore the most effective route for improving the resistance of carburized 18CrNiMo7-6 gears to micropitting and pitting.
Related
- Total Phenylethanoid Glycosides from Cistanche tubulosa Alleviate 5-Fluorouracil-Induced Fatigue-Like Behavior and Skeletal Muscle Injury in Mice
- Real-time assessment of temperature sensitivity, pain processing, and pain behavior across the lifespan: Integrating stimulus data, contact force, and subjective ratings.
- Effects of chronic oxytocin administration on white matter microstructure in autistic adults: a pilot pharmaco-neuroimaging DTI study
- Neurite orientation dispersion and density imaging for preoperative evaluation of cerebral microstructure and neurodevelopment in children with congenital heart disease
- Diffusion Basis Spectrum Imaging of Tissue Microstructure and Early Treatment in Multiple Sclerosis
BibTeX
@article{wu2026analysis,
title = {{Analysis of contact fatigue behavior of 18CrNiMo7-6 gears based on surface integrity and microstructure}},
author = {Luji Wu and Zhongchao Bai and Anhu Li and Jiayin Qin and Yalong Zhang},
journal = {Scientific Reports},
year = {2026},
month = jul,
doi = {10.1038/s41598-026-63593-x},
url = {https://doi.org/10.1038/s41598-026-63593-x},
note = {CC BY},
}
RIS
TY - JOUR
TI - Analysis of contact fatigue behavior of 18CrNiMo7-6 gears based on surface integrity and microstructure
AU - Luji Wu
AU - Zhongchao Bai
AU - Anhu Li
AU - Jiayin Qin
AU - Yalong Zhang
PY - 2026
DA - 2026/07/01
JO - Scientific Reports
DO - 10.1038/s41598-026-63593-x
UR - https://doi.org/10.1038/s41598-026-63593-x
AB - This study aims to clarify how different initial surface states affect the micropitting and pitting behavior of carburized 18CrNiMo7-6 gears. Gears subjected to grinding, shot peening, and shot peening followed by barrel finishing were tested under the same contact fatigue conditions for a preset duration of 5.0 × 107 cycles. Case 1-SPC consisted of carburizing and grinding, followed by shot peening and barrel finishing. Case 2-SPS consisted of carburizing and grinding, followed by shot peening. Case 3-RC consisted of carburizing and grinding only. The results show that micropitting and pitting are governed by the coupled evolution of surface topography, hardness gradient, residual stress, and near-surface microstructure. All cases exhibited near-surface softening after cycling, while the redistribution of the hardness gradient strongly depended on the initial surface state. Shot peening introduced a high magnitude compressive residual stress field, and after cycling the maximum compressive residual stress in Case 1-SPC remained as high as 977.85 MPa, although this condition also showed the most pronounced stress relaxation. In contrast, barrel finishing produced a smoother and more surface oriented compressive stress distribution with better stability, and Case 1-SPC exhibited the best resistance to both micropitting and pitting. Surface observations showed a regional micropitting band in Case 1-SPC, denser micropitting in Case 2-SPS, and larger localized pitting in the ground condition. In addition, cyclic contact loading induced grain refinement, elevated local orientation gradients, and enhanced plastic heterogeneity in the near-surface layer. After cycling, Case 1-SPC showed the most pronounced microstructural reconstruction, with an average grain size refined to 0.57 μm and an average geometrically necessary dislocation (GND) density increased to 19.99 × 1014 m-2. Overall, shot peening followed by barrel finishing provided the most favorable balance among residual stress stability, surface integrity retention, and damage suppression, and was therefore the most effective route for improving the resistance of carburized 18CrNiMo7-6 gears to micropitting and pitting.
SN - 2045-2322
ER -