Aluminum-Doped Zinc Oxide Ceramics with Improved Thermoelectric Properties via a Simple Pechini Based Sol Gel Method
Abstract
In this study, zinc oxide (ZnO) ceramics were synthesized by a modified Pechini sol-gel method, replacing conventional zinc nitrate with zinc acetate to provide a distinct chemical environment and avoid toxic emissions during heat treatment. To the best of our knowledge, this work represents the first time this acetate-based Pechini route is investigated from a thermoelectric perspective. This approach offers a scalable, inexpensive, and non-toxic route with precise compositional control. To enhance thermoelectric performance, the powders were doped with 2% aluminum and subjected to optimized mechanical milling before sintering. Structural and microstructural characterizations confirmed the formation of a pure ZnO wurtzite phase with well-distributed dopants and refined grain morphology. Thermoelectric measurements revealed that aluminum doping significantly increases electrical conductivity. The best results were obtained for milled ZnO-2%Al powders sintered at 1400 °C for 6 h, yielding a Seebeck coefficient of -150 µV. K − 1 and a power factor of 138 µW.m − 1 . K − 2 at 700 °C. The corresponding ZT value reaches 0.012, demonstrating that this protocol provides a highly effective and industrially scalable alternative to more complex, capital-intensive methods such as Spark Plasma Sintering (SPS). An original analysis based on an effective medium approach (EMA) is presented to decouple the competing effects of porosity and doping. We demonstrate that while the system is highly sensitive to connectivity losses induced by porosity, the electronic gain from aluminum doping significantly overshadows these structural penalties. These results confirm the potential of the acetate-based Pechini method, combined with controlled doping and milling, as a simple, cost-effective, and processing-flexible route, paving the way for both bulk ceramics and easy-to-deposit thick or thin film geometries for the industrial-scale development of oxide-based thermoelectric materials.
Related
- Machine Learning-Driven Prediction and Optimization of Thermoelectric Transport Properties in Ce-Doped CaMnO3 Ceramics
- Synthesis and characterization of luminescent properties of ceramics derived from polysilylcarbodiimides
- Improved efficiency for better resolved solid-state NMR studies of Aluminum sites in materials
- Effect of fluorine addition on the microstructure and emission properties of Ho:Y2O3 transparent ceramics
- Effect of Sm and Ni co-doping on optical and electrical properties of lead magnesate niobate titanate ceramics
BibTeX
@article{drame2026aluminumdoped,
title = {{Aluminum-Doped Zinc Oxide Ceramics with Improved Thermoelectric Properties via a Simple Pechini Based Sol Gel Method}},
author = {Nouha Drame and Gerard Leroy and Fabien Giovannelli and Michael Depriester and Jean-Claude Carru},
journal = {Transactions on Electrical and Electronic Materials},
year = {2026},
month = jun,
doi = {10.1007/s42341-026-00717-0},
url = {https://hal.science/hal-05734145v1},
note = {CC BY},
}
RIS
TY - JOUR
TI - Aluminum-Doped Zinc Oxide Ceramics with Improved Thermoelectric Properties via a Simple Pechini Based Sol Gel Method
AU - Nouha Drame
AU - Gerard Leroy
AU - Fabien Giovannelli
AU - Michael Depriester
AU - Jean-Claude Carru
PY - 2026
DA - 2026/06/27
JO - Transactions on Electrical and Electronic Materials
DO - 10.1007/s42341-026-00717-0
UR - https://hal.science/hal-05734145v1
AB - In this study, zinc oxide (ZnO) ceramics were synthesized by a modified Pechini sol-gel method, replacing conventional zinc nitrate with zinc acetate to provide a distinct chemical environment and avoid toxic emissions during heat treatment. To the best of our knowledge, this work represents the first time this acetate-based Pechini route is investigated from a thermoelectric perspective. This approach offers a scalable, inexpensive, and non-toxic route with precise compositional control. To enhance thermoelectric performance, the powders were doped with 2% aluminum and subjected to optimized mechanical milling before sintering. Structural and microstructural characterizations confirmed the formation of a pure ZnO wurtzite phase with well-distributed dopants and refined grain morphology. Thermoelectric measurements revealed that aluminum doping significantly increases electrical conductivity. The best results were obtained for milled ZnO-2%Al powders sintered at 1400 °C for 6 h, yielding a Seebeck coefficient of -150 µV. K − 1 and a power factor of 138 µW.m − 1 . K − 2 at 700 °C. The corresponding ZT value reaches 0.012, demonstrating that this protocol provides a highly effective and industrially scalable alternative to more complex, capital-intensive methods such as Spark Plasma Sintering (SPS). An original analysis based on an effective medium approach (EMA) is presented to decouple the competing effects of porosity and doping. We demonstrate that while the system is highly sensitive to connectivity losses induced by porosity, the electronic gain from aluminum doping significantly overshadows these structural penalties. These results confirm the potential of the acetate-based Pechini method, combined with controlled doping and milling, as a simple, cost-effective, and processing-flexible route, paving the way for both bulk ceramics and easy-to-deposit thick or thin film geometries for the industrial-scale development of oxide-based thermoelectric materials.
SN - 1229-7607
SN - 2092-7592
ER -