Microstructure, thermal conductivity and mechanical anisotropy of DURACON 45M fabricated by laser-wire directed energy deposition
Abstract
High-thermal-conductivity tool materials are critical for reducing cooling-limited cycle times in polymer processing. Microstructure, mechanical anisotropy and thermal conductivity of the Fe–Co–Ni alloy DURACON 45M fabricated by laser-wire directed energy deposition (LW-DED) are investigated. The as-built material exhibits near-full density and a direction-dependent microstructure. EBSD analysis showed a refined grain structure with grain sizes predominantly below 10 µm in the X direction, while the Z direction contained coarser grains elongated along the thermal gradient. In comparison, the wrought base material (BM) exhibited grain sizes mainly around 10 µm. Mechanical testing revealed significantly enhanced tensile strength in the build plane, whereas ductility was markedly reduced along the build direction due to the anisotropic microstructure consisting of elongated columnar grains and crystallographic texture. Despite these microstructural changes, the thermal conductivity remained high ( ∼ 68 W m−1 K−1 ). No measurable anisotropy was observed within the uncertainty of the present measurements, and the values remained comparable to those of the base material. These results demonstrate the potential of LW-DED DURACON 45M produced using the investigated processing conditions for advanced tooling applications while emphasizing build-direction anisotropy as a key design constraint.
Related
- Influence of Lamella Structure on Mechanical Properties and Corrosion Resistance of AlCoCrFeNi2.1 Eutectic High-Entropy Alloy Fabricated by Laser-Based Directed Energy Deposition
- Interfacial Microstructure and Tensile–Shear Properties of AA1060/SUS304 Dissimilar Sheet Joints Fabricated by Uniform-Pressure Electromagnetic Pulse Welding
- A Numerical Study of the Microstructure-Dependent Thermal Conductivity of Diamond-Reinforced Sintered Silver Composites
- Effect of pyrolysis temperature on the microstructure and thermal conductivity of polymer-derived monolithic and porous SiC ceramics
- Study on microstructure and properties of titanium alloy wall fabricated by laser-TIG arc
BibTeX
@article{hodek2026microstructure,
title = {{Microstructure, thermal conductivity and mechanical anisotropy of DURACON 45M fabricated by laser-wire directed energy deposition}},
author = {Josef Hodek and Petr Motycka and David Hradil and Matouš Uhlík and Zdeněk Jansa and Pavel Salvetr},
journal = {Scientific Reports},
year = {2026},
month = oct,
doi = {10.1038/s41598-026-74788-7},
url = {https://www.nature.com/articles/s41598-026-74788-7},
note = {CC BY 4.0},
}
RIS
TY - JOUR
TI - Microstructure, thermal conductivity and mechanical anisotropy of DURACON 45M fabricated by laser-wire directed energy deposition
AU - Josef Hodek
AU - Petr Motycka
AU - David Hradil
AU - Matouš Uhlík
AU - Zdeněk Jansa
AU - Pavel Salvetr
PY - 2026
DA - 2026/10/08
JO - Scientific Reports
DO - 10.1038/s41598-026-74788-7
UR - https://www.nature.com/articles/s41598-026-74788-7
AB - High-thermal-conductivity tool materials are critical for reducing cooling-limited cycle times in polymer processing. Microstructure, mechanical anisotropy and thermal conductivity of the Fe–Co–Ni alloy DURACON 45M fabricated by laser-wire directed energy deposition (LW-DED) are investigated. The as-built material exhibits near-full density and a direction-dependent microstructure. EBSD analysis showed a refined grain structure with grain sizes predominantly below 10 µm in the X direction, while the Z direction contained coarser grains elongated along the thermal gradient. In comparison, the wrought base material (BM) exhibited grain sizes mainly around 10 µm. Mechanical testing revealed significantly enhanced tensile strength in the build plane, whereas ductility was markedly reduced along the build direction due to the anisotropic microstructure consisting of elongated columnar grains and crystallographic texture. Despite these microstructural changes, the thermal conductivity remained high ( ∼ 68 W m^−1 K^−1 ). No measurable anisotropy was observed within the uncertainty of the present measurements, and the values remained comparable to those of the base material. These results demonstrate the potential of LW-DED DURACON 45M produced using the investigated processing conditions for advanced tooling applications while emphasizing build-direction anisotropy as a key design constraint.
SN - 2045-2322
ER -