Increasing the Impact Strength of Grass Fiber Polypropylene Composites with Virgin and Recycled Polypropylene
- 1Department of Mechanical and Plastics Engineering, Darmstadt University of Applied Sciences, 64295 Darmstadt, Germany
Abstract
Natural fibers from different plants are widely used as reinforcing fillers in polymers due to their ecological, economic and technical benefits, with applications in all major industries. Since a typical drawback of incorporating natural fibers into polymers is a reduction in impact strength, this work investigates ways to enhance impact strength. Grass fibers of 30 wt. % from permanent pasture grasslands are compounded with polypropylene and varying amounts of polypropylene-graft-maleic anhydride with three different degrees of grafting as coupling agents and ethylene propylene diene rubber as the impact modifier. The impact strength and the melt flow index are measured for each compound while the adhesion between the fibers and matrix is investigated by scanning electron microscopy. It can be shown that around 5 wt. % of coupling agents are sufficient to increase impact strength to a saturation level, while the impact modifier has no significant influence. Through multiple extrusion cycles of a pure grass fiber polypropylene compound, it can be shown that the melt flow index increases constantly with the number of extrusion cycles, while the impact strength remains constant after an initial increase, indicating matrix degradation but enhanced fiber matrix coupling.
Related
- Upcycling Secondary Cellulosic Fibres and Post-Industrial Recycled Polypropylene from Household Appliance Manufacturing into Circular Composites with Enhanced Dimensional Stability
- Study of Hybrid Epoxy Resin Composites Reinforced with E-CR Glass Fiber/Polypropylene: Moisture Behavior, Mechanical Strength, and Acoustic Damage Mitigation Under Marine Aging Conditions
- Increasing both strength and toughness in ceramic-matrix composites via bioinspired porous interphases
- Low-Velocity Impact Response of Biaxial Glass-Fiber Fabric Composites: Influence of Fabric Layer Number Under Progressively Increasing Impact Energy
- Degradation-Grafting Mechanochemical Treatment of Recycled Polypropylene as an Asphalt Modifier: Rheological Behavior and Microscopic Mechanisms
BibTeX
@article{grunheide2026increasing,
title = {{Increasing the Impact Strength of Grass Fiber Polypropylene Composites with Virgin and Recycled Polypropylene}},
author = {Katharina Grünheide and Eric Stuckert and Heiko Hofmann and Martin Moneke},
journal = {Polymers},
year = {2026},
month = oct,
doi = {10.3390/polym18202540},
url = {https://www.mdpi.com/2073-4360/18/20/2540},
note = {CC BY 4.0},
}
RIS
TY - JOUR
TI - Increasing the Impact Strength of Grass Fiber Polypropylene Composites with Virgin and Recycled Polypropylene
AU - Katharina Grünheide
AU - Eric Stuckert
AU - Heiko Hofmann
AU - Martin Moneke
PY - 2026
DA - 2026/10/16
JO - Polymers
DO - 10.3390/polym18202540
UR - https://www.mdpi.com/2073-4360/18/20/2540
AB - Natural fibers from different plants are widely used as reinforcing fillers in polymers due to their ecological, economic and technical benefits, with applications in all major industries. Since a typical drawback of incorporating natural fibers into polymers is a reduction in impact strength, this work investigates ways to enhance impact strength. Grass fibers of 30 wt. % from permanent pasture grasslands are compounded with polypropylene and varying amounts of polypropylene-graft-maleic anhydride with three different degrees of grafting as coupling agents and ethylene propylene diene rubber as the impact modifier. The impact strength and the melt flow index are measured for each compound while the adhesion between the fibers and matrix is investigated by scanning electron microscopy. It can be shown that around 5 wt. % of coupling agents are sufficient to increase impact strength to a saturation level, while the impact modifier has no significant influence. Through multiple extrusion cycles of a pure grass fiber polypropylene compound, it can be shown that the melt flow index increases constantly with the number of extrusion cycles, while the impact strength remains constant after an initial increase, indicating matrix degradation but enhanced fiber matrix coupling.
SN - 2073-4360
ER -