Effect of bleaching-remineralization sequence on enamel microhardness and surface properties during laser-assisted bleaching.
- 1Department of Restorative Dentistry, Hacettepe University, Ankara, Turkey. [email protected].
- 2Department of Restorative Dentistry, Hacettepe University, Ankara, Turkey.
Abstract
This in vitro study evaluated whether the sequence of bleaching and remineralization procedures and the type of remineralizing agent influence enamel microhardness, surface roughness, and color change following diode laser-assisted bleaching. One hundred twenty human enamel specimens were randomly assigned to two treatment sequences: Bleach-First (BF) and Remineralize-First (RF), each further subdivided into four groups (n = 15) representing different remineralization mechanisms (CPP-ACP-based, calcium-phosphate-magnesium, hydroxyapatite-based, and fluoride varnish). Bleaching was performed using a 35% hydrogen peroxide gel (Whiteness HP, FGM) activated with a 940-nm diode laser (Epic X, Biolase; 7 W, continuous-wave mode; total irradiation time: 120 s). Surface microhardness (VHN; 200 g load for 15 s), surface roughness (Ra), and color (ΔE00) were measured at baseline and after each procedural stage. Data were statistically analyzed using repeated-measures and two-way ANOVA (α = 0.05). A significant difference between treatment sequences was observed at the initial stage (p < 0.001), with bleaching reducing and remineralization increasing microhardness. A significant time × sequence interaction (p < 0.001) indicated that these changes depended on the order of application, while no significant main effect of remineralizing agent or sequence × agent interaction was detected (p > 0.05). Surface roughness values showed no significant differences between sequences or agents, except for a transient increase in the fluoride varnish group in the RF sequence. Similarly, all groups exhibited clinically acceptable color change, with no significant differences between sequences or agents. SEM/EDS analyses further revealed sequence-dependent surface alterations, supporting the microhardness findings. The sequence of bleaching and remineralization procedures was identified as the primary factor influencing enamel microhardness, whereas the type of remineralizing agent had no significant effect. Remineralization applied after bleaching appears more effective for restoring enamel microhardness, without affecting surface roughness or color outcomes. Within the limitations of this in vitro study, post-bleaching remineralization demonstrated favorable effects on enamel microhardness without compromising bleaching efficacy.
Related
- Application of AI-assisted compressed sensing cine sequence in the assessment of cardiac function in children with Kawasaki disease
- Effects of keiser-assisted Nordic hamstring curl training on hamstring flexibility, mechanical properties, and pitching performance in high school baseball pitchers
- Salivary Citrate Deficiency Defines an Endogenous Dentin Remineralization Failure State Through Glandular MT1/2-Zn²⁺-ACO2 Dysregulation.
- Comparative evaluation of the remineralization potential of chitosan-fluoride-doped mesoporous silica nanoparticles hydrogel and casein phosphopeptide-amorphous calcium phosphate fluoride paste on the enamel of primary teeth: An in vitro study
- An in vitro comparative study of the effects of soy milk and coconut milk on the microhardness of primary molar enamel after an acidic challenge.
BibTeX
@article{tekce2026effect,
title = {{Effect of bleaching-remineralization sequence on enamel microhardness and surface properties during laser-assisted bleaching.}},
author = {Aybuke Uslu Tekce and Kemal Işıklı and Ece Meral and Filiz Yalcin Cakir},
journal = {Lasers in medical science},
year = {2026},
month = oct,
doi = {10.1007/s10103-026-04983-5},
url = {https://europepmc.org/article/MED/42907680},
note = {CC BY-NC-ND},
}
RIS
TY - JOUR
TI - Effect of bleaching-remineralization sequence on enamel microhardness and surface properties during laser-assisted bleaching.
AU - Aybuke Uslu Tekce
AU - Kemal Işıklı
AU - Ece Meral
AU - Filiz Yalcin Cakir
PY - 2026
DA - 2026/10/22
JO - Lasers in medical science
DO - 10.1007/s10103-026-04983-5
UR - https://europepmc.org/article/MED/42907680
AB - This in vitro study evaluated whether the sequence of bleaching and remineralization procedures and the type of remineralizing agent influence enamel microhardness, surface roughness, and color change following diode laser-assisted bleaching. One hundred twenty human enamel specimens were randomly assigned to two treatment sequences: Bleach-First (BF) and Remineralize-First (RF), each further subdivided into four groups (n = 15) representing different remineralization mechanisms (CPP-ACP-based, calcium-phosphate-magnesium, hydroxyapatite-based, and fluoride varnish). Bleaching was performed using a 35% hydrogen peroxide gel (Whiteness HP, FGM) activated with a 940-nm diode laser (Epic X, Biolase; 7 W, continuous-wave mode; total irradiation time: 120 s). Surface microhardness (VHN; 200 g load for 15 s), surface roughness (Ra), and color (ΔE00) were measured at baseline and after each procedural stage. Data were statistically analyzed using repeated-measures and two-way ANOVA (α = 0.05). A significant difference between treatment sequences was observed at the initial stage (p < 0.001), with bleaching reducing and remineralization increasing microhardness. A significant time × sequence interaction (p < 0.001) indicated that these changes depended on the order of application, while no significant main effect of remineralizing agent or sequence × agent interaction was detected (p > 0.05). Surface roughness values showed no significant differences between sequences or agents, except for a transient increase in the fluoride varnish group in the RF sequence. Similarly, all groups exhibited clinically acceptable color change, with no significant differences between sequences or agents. SEM/EDS analyses further revealed sequence-dependent surface alterations, supporting the microhardness findings. The sequence of bleaching and remineralization procedures was identified as the primary factor influencing enamel microhardness, whereas the type of remineralizing agent had no significant effect. Remineralization applied after bleaching appears more effective for restoring enamel microhardness, without affecting surface roughness or color outcomes. Within the limitations of this in vitro study, post-bleaching remineralization demonstrated favorable effects on enamel microhardness without compromising bleaching efficacy.
SN - 0268-8921
SN - 1435-604X
ER -