Passive Thermal Management of Cylindrical Lithium-Ion Cells Using Additively Manufactured Polymer Housings
- 1Central Campus Győr, Széchenyi István University, 9026 Győr, Hungary
Abstract
Lithium-ion batteries are widely used in modern energy storage systems; however, increasing power demand makes thermal management a critical challenge, particularly for cylindrical cells operating under high discharge conditions. This study investigates the thermal behavior of cylindrical lithium-ion cells equipped with additively manufactured polymer housings produced by fused filament fabrication (FFF). PLA, PCTG, flame-retardant PLA (FG_PLA), and ASA housings were evaluated using Samsung 50S, Molicel P42A, and Reliance RS50 cells under 1C–5C discharge rates. Surface temperatures were measured at multiple locations to assess heat transfer through the housing structures. All investigated housings reduced the measured maximum cell surface temperature compared with the housing-free configuration, particularly at high discharge rates. PLA exhibited the greatest thermal buffering effect, while PCTG showed the highest estimated conductive heat-transfer rate and a more uniform temperature evolution across the housing. ASA demonstrated stable thermal behavior, with thin housings generally showing a greater measured temperature reduction than thick configurations. In contrast, flame-retardant PLA provided the smallest temperature reduction. Wall thickness influenced the transient thermal response but did not consistently result in a greater measured temperature reduction. At elevated temperatures, partial deformation of some polymer housings was observed. The results demonstrate that FFF-manufactured polymer housings can substantially modify the transient thermal response of cylindrical lithium-ion cells, while material selection and housing geometry remain key design parameters for passive thermal management applications.
Related
- Influence of Post-Processing by Annealing on Additive Manufacturing Productivity and Mechanical Properties in Three-Point Bending of Additively Manufactured Specimens from PETG and Recycled PETG
- Temperature-dependent deformation behavior of the additively manufactured Al0.75CrFeNi2.1 alloy using in-situ high energy X-ray diffraction
- Experimental and Numerical Analysis of the Strain Response of Additively Manufactured Composites
- Mechanical Performance of Bio-Based Additively Manufactured Honeycomb Sandwich Panels: Experimental and Numerical Investigation
- Heat Treatment Effects on Additively Manufactured Polymer Matrix Composites
BibTeX
@article{szurke2026passive,
title = {{Passive Thermal Management of Cylindrical Lithium-Ion Cells Using Additively Manufactured Polymer Housings}},
author = {Szabolcs Kocsis Szürke and Brigitta Fruzsina Szívós and Kornél László and Illés Lőricz and Levente Eördögh},
journal = {Batteries},
year = {2026},
month = oct,
doi = {10.3390/batteries12100413},
url = {https://www.mdpi.com/2313-0105/12/10/413},
note = {CC BY 4.0},
}
RIS
TY - JOUR
TI - Passive Thermal Management of Cylindrical Lithium-Ion Cells Using Additively Manufactured Polymer Housings
AU - Szabolcs Kocsis Szürke
AU - Brigitta Fruzsina Szívós
AU - Kornél László
AU - Illés Lőricz
AU - Levente Eördögh
PY - 2026
DA - 2026/10/10
JO - Batteries
DO - 10.3390/batteries12100413
UR - https://www.mdpi.com/2313-0105/12/10/413
AB - Lithium-ion batteries are widely used in modern energy storage systems; however, increasing power demand makes thermal management a critical challenge, particularly for cylindrical cells operating under high discharge conditions. This study investigates the thermal behavior of cylindrical lithium-ion cells equipped with additively manufactured polymer housings produced by fused filament fabrication (FFF). PLA, PCTG, flame-retardant PLA (FG_PLA), and ASA housings were evaluated using Samsung 50S, Molicel P42A, and Reliance RS50 cells under 1C–5C discharge rates. Surface temperatures were measured at multiple locations to assess heat transfer through the housing structures. All investigated housings reduced the measured maximum cell surface temperature compared with the housing-free configuration, particularly at high discharge rates. PLA exhibited the greatest thermal buffering effect, while PCTG showed the highest estimated conductive heat-transfer rate and a more uniform temperature evolution across the housing. ASA demonstrated stable thermal behavior, with thin housings generally showing a greater measured temperature reduction than thick configurations. In contrast, flame-retardant PLA provided the smallest temperature reduction. Wall thickness influenced the transient thermal response but did not consistently result in a greater measured temperature reduction. At elevated temperatures, partial deformation of some polymer housings was observed. The results demonstrate that FFF-manufactured polymer housings can substantially modify the transient thermal response of cylindrical lithium-ion cells, while material selection and housing geometry remain key design parameters for passive thermal management applications.
SN - 2313-0105
ER -