Hydrogel Scaffold Printing Assisted by Substrate Cooling and an Electric Field
- 1State Key Laboratory of High-Performance Precision Manufacturing, Dalian University of Technology, Dalian 116024, China
- 2Ningbo Institute of Dalian University of Technology, Ningbo 315032, China
- 3School of Mechanical and Electrical Engineering, Zhengzhou University of Light Industry, Zhengzhou 450002, China
Abstract
Lateral spreading and deformation during layer stacking limit the geometric fidelity of extrusion-printed hydrogel scaffolds. To address these constraints, this study presents an extrusion-printing strategy that combines electrical assistance and substrate cooling for poly(vinyl alcohol)/gelatin methacryloyl/alginate hydrogels. Electrical assistance improved filament uniformity in the simulations and independent controls, while separate cooling controls showed better preservation of lattice openings. The process produced filaments approximately 152 μm wide, and connected patterns retained distinct corners, curved boundaries and junctions. Three independently printed grids yielded a square-pore printability index of 0.9256 ± 0.0034. Three ten-layer specimens also retained open pores and reached a mean height of approximately 1.40 mm. After printing, ultraviolet irradiation and three freeze–thaw cycles stabilized the constructs. Compression tests on cast hydrogel specimens showed increasing resistance to deformation with additional freeze–thaw cycles. Curved patterns, structures of different heights and a meniscus-shaped construct further demonstrated the range of printable geometries. Together, these results support the strategy for fine filament deposition and open multilayer construction in this hydrogel blend.
Related
- Stem cell-assisted aligned electrospun nanofiber scaffold for tissue engineering: development to application.
- Computational insights into the electrostatic origins of mechanistic selectivity: human topoisomerase IIα enforces ATP hydrolysis via substrate-assisted catalysis.
- PDA-Assisted Fabrication of Calcium Alginate Hydrogel-Coated Stainless Steel Meshes for High-Efficiency Oil/Water Separation
- Bio-based cellulose-filled vitrimers for 3D printing via liquid deposition modeling: Rheological tuning and environmental assessment
- Bioinspired 4D‐Printing Microwave Absorbers With Adaptive Programmable Switches via Morphable Percolation Networks and Resonant Models
BibTeX
@article{jin2026hydrogel,
title = {{Hydrogel Scaffold Printing Assisted by Substrate Cooling and an Electric Field}},
author = {Wenbo Jin and Ruoyu Wang and Wenyu Ning and Fei Duan and Liangkun Lu and Cheng Zhang and Heqi Xu and Kedong Song and Danyang Zhao},
journal = {Polymers},
year = {2026},
month = oct,
doi = {10.3390/polym18202579},
url = {https://www.mdpi.com/2073-4360/18/20/2579},
note = {CC BY 4.0},
}
RIS
TY - JOUR
TI - Hydrogel Scaffold Printing Assisted by Substrate Cooling and an Electric Field
AU - Wenbo Jin
AU - Ruoyu Wang
AU - Wenyu Ning
AU - Fei Duan
AU - Liangkun Lu
AU - Cheng Zhang
AU - Heqi Xu
AU - Kedong Song
AU - Danyang Zhao
PY - 2026
DA - 2026/10/01
JO - Polymers
DO - 10.3390/polym18202579
UR - https://www.mdpi.com/2073-4360/18/20/2579
AB - Lateral spreading and deformation during layer stacking limit the geometric fidelity of extrusion-printed hydrogel scaffolds. To address these constraints, this study presents an extrusion-printing strategy that combines electrical assistance and substrate cooling for poly(vinyl alcohol)/gelatin methacryloyl/alginate hydrogels. Electrical assistance improved filament uniformity in the simulations and independent controls, while separate cooling controls showed better preservation of lattice openings. The process produced filaments approximately 152 μm wide, and connected patterns retained distinct corners, curved boundaries and junctions. Three independently printed grids yielded a square-pore printability index of 0.9256 ± 0.0034. Three ten-layer specimens also retained open pores and reached a mean height of approximately 1.40 mm. After printing, ultraviolet irradiation and three freeze–thaw cycles stabilized the constructs. Compression tests on cast hydrogel specimens showed increasing resistance to deformation with additional freeze–thaw cycles. Curved patterns, structures of different heights and a meniscus-shaped construct further demonstrated the range of printable geometries. Together, these results support the strategy for fine filament deposition and open multilayer construction in this hydrogel blend.
SN - 2073-4360
ER -